HOME  

ENQUIRE

Click images to enlarge

20MVA Cast Resin Transformer with On-load Tap Changer - Two of these transformers are installed in a major Sydney facility.  Each transformer has a capacity of 20MVA, is rated at 33000/11000 Volts and is fitted with on-load tap changers to provide constant 11000V to the building.  The building is fitted with a further 53 TMC Cast Resin Distribution transformers rated between 500kVA and 2500kVA to provide low voltage at the load centres.

10MVA Cast Resin Transformer with On-load Tap Changer
Two of these transformers are installed in a major Shanghai facility.  Each transformer has a capacity of 10MVA, is rated at 35000/10000 Volts and is fitted with on-load tap changers to provide constant 10000V to the building.  The building is fitted with a further 9 TMC Cast Resin Distribution transformers rated at 2400kVA to provide low voltage at the load centres.

1500kVA Distribution Transformer in IP20 Enclosure
The 1500kVA 11000/433V Cast Resin Distribution Transformer shown is typical of TMC's range of transformers supplied in large numbers to utilities in the United Arab Emirates.  The construction features a slim line design with terminal boxes located on the narrow ends.

33kV Outdoor Cast Resin Transformer
This photo shows a detail of a 2000kVA 33000/3300V outdoor cast resin transformer.  Two of which were purchased by an Australian power utility for outdoor use in an environment where the risk of oil contamination was unacceptable.  By using cast resin transformers, the utility reduces insurance premium costs by totally eliminating the risk of environmental oil contamination and achieves the further benefit of reduced fire risk.

TMC Cast Resin Transformers Power this P+H MinePro Shovel
Built into this impressive P+H MinePro Australia Mining Shovel are two TMC Cast Resin Transformers.  The power to the motors is supplied by one 2500kVA 11000-6600 / 600-600V Dy1y1 IP43 Cast Resin Rectifier Transformer.  The auxiliary power requirements are supplied from one 325kVA transformer with multiple secondary windings.  The transformers are designed to withstand the arduous mechanical shocks and vibrations experienced by the shovel.

Outdoor Cast Resin Transformers at a major Australia Mine
27 TMC Cast Resin Transformers are installed at this Australian mine.  The transformers range from 1000kVA to 3500kVA and are installed throughout the processing plant close to the loads.  A further 15 low voltage 200kVA and 400kVA transformers are installed for lighting and other auxiliary power requirements.  By using Cast Resin Transformers, the mine reduces the risk of fire and eliminates possible environmental contamination by transformer oil spills.

11kV Outdoor Current Limiting Cast Resin Reactors
The photo shows a three phase set of 6.50mH 11kV 650A reactors installed at a modern power generation plant. The reactors limit the potential fault current between the generator and grid to a safe level. The reactors are stacked to present a small footprint.

Marshalling Box
This photo shows a detail of a marshalling box on an enclosure.  The marshalling box is sealed and lockable if required.

33kV Outdoor Cast Resin Rectifier Transformer in Stainless Steel Enclosure
This stainless steel outdoor enclosure houses a 2700kVA 33000 / 600-600V Cast Resin Rectifier Transformer.  Six similar units are installed along a major rail route in New South Wales.  The stainless steel enclosure was chosen to meet the corosion requirements of the coastal environment into which the transformers are installed.

X-Ray Transformer Produced by TMC
Copy of an article appearing in the Melbourne "Argus" showing a 125kVp X-Ray Transformer undergoing testing prior to export.  TMC has manufactured high voltage X-Ray transformers up to 500kVp.

1975 TMC Transformer-Rectifier With Electronic Control
This photo shows a 50kV 500mA Oil Cooled Transformer-Rectifier with thyristor control.  TMC manufactured 75 such units for use at the Allied Eneabba mineral sands project near Geraldton Western Australia.

Indoor Cast Resin Transformer Installation
TMC Cast Resin Distribution and Power transformers are ideal for indoor installation. The photo shows a typical installation.  LV busway can be seen connected directly to the transformer.  The TMC transformer is fitted with internal busway connection links.  The installation contractor simply attaches the busway end to the enclosure flange (deisgned to match) and then attached the pre-measured and supplied internal flexible links.  By using Cast Resin Transformers, the city building reduces the risk of fire and eliminates possible environmental contamination by transformer oil spills.